Fall River Hydraulic Hoses: Replace Worn Hoses and Fittings

Most of the hydraulic hose fittings and hose materials that you will use in an industrial or professional setting are designed for heavy use. However, nothing is designed to last forever. You need to stay on top of regular inspections and replace worn hoses and fittings before a failure occurs. Replacing your Fall River hydraulic hoses should be a top priority, as failures can result in severe injury to operators and other employees, as well as serious damage to equipment. Learn to spot the signs of wear and tear in your unique environment and visit your local hydraulic hose shop in Fall River to get all of the industry supply and services you need to get the job done right.

Determine What Needs to Be Fixed

Start by performing a visual inspection of the entire hydraulic system without touching hoses or fittings. This is an integral part of the process to replace worn hoses and fittings safely. If you notice that anything is damaged or leaking, note the area where you see the problem and prepare to safely shut down the system to take care of the repairs. Always use proper safety gear and protocol to prevent injury to yourself or other employees. Start by relieving the pressure on the hydraulic cylinders. This will prevent a blow-out and make the process of replacing your Fall River hydraulic hoses a lot safer.

The next step is to safely remove the hose components. This must be done before you can replace the broken or damaged hose fittings or replace worn hoses on your machinery. Check with the manufacturer’s recommendations in the owner’s manual or use an in-house repair manual to make sure you don’t miss a strategic step in the process. Clamps, guards, the housing, and other components may need to be removed before you can even get at the broken or damaged fittings. If this is your first time doing this process, make notes or take photos of each item before you remove it so it will be easier to return it to the proper place after the hydraulic hose fittings and hoses are replaced.

Start Removing the Hose Fittings and Hoses

The next phase of the project for safe replacement of Fall River hydraulic hoses is to remove the hose fittings. Some types of hose fittings have a swivel feature that must be removed using two wrenches. The swivel is designed to work when the pump is on, but when it is off you need to clamp one wrench on one side of the coupling to hold the piece steady and a second wrench on the other side to turn the coupling. It can take a bit to get it the first time, but once you’ve done it and see how it works, it’s very easy to do. If you experience couplings that are stuck or difficult to move, you might need to use some lubricant to get them loose.

If the hose needs to be replaced, make sure also to loosen any fittings that are attached to the hose itself and pull it out so you can inspect it. If you aren’t sure what size you need from the local industrial supply and services shop, bring it in with you. Once the hose is removed, you can start cleaning all of the fittings them to make sure that no dirt or debris can enter your machine and cause contamination. If your fittings need to be replaced, bring them into the hydraulic hose shop in Fall River as well so you can make sure to get the right type. Once you have everything you need you can start to put the fittings back together and install them in their proper places. Return any cylinder pins and snap rings designed to hold the pins in place to make sure everything is secure.

Where to Go for Hydraulic Hoses in Fall River

If you are in need of parts to replace worn hoses and fittings in the Greater Fall River area, visit Metro Industrial in New Bedford. We have a large selection of industrial supply and services but are most known for our custom hydraulic shop in Fall River and the surrounding area. People come from as far as Boston and Providence to visit our shop and place custom orders online or over the phone from all over the globe. We specialize in custom hydraulic hoses and hydraulic hose assemblies. Our team can custom make-to-order hoses unlike any other supplier in the area. We can offer up to ” 1-6 wire hydraulic hoses, depending on the needs of our customers, including four spiral, ultra-high pressure and low pressure, crimp fittings, steel brass, and stainless steel, plus US and metric ends. Give us a call at 508-996-8400 or stop by our location on Coggeshall Street in New Bedford, MA.